Honeywell RTH230Bमैनुअल

Honeywell RTH230B
9.2 · 2
PDF हाथ से किया हुआ
 · 4 पृष्ठों
अंग्रेज़ी
हाथ से किया हुआHoneywell RTH230B
RTH230B 69-1800 2/6/05 1/4
The RTH230B programmable thermostat can be used to control:
a gas, fuel oil or electric furnace - 2 or 3 wires
a central air conditioner - 2 or 3 wires
a hot water system with or without pump - 2 wires
a millivolt system - 2 wires
a central heating and cooling system - 4 or 5 wires
Note: These thermostats are not compatible with heat pumps or
multi-stage systems.
Features
System operating mode selection: heat, cool or off
Fan operating mode selection: automatic or on (continuous)
Programmable heating and cooling cycle lengths: 10, 12, 15, 20
or 30 minutes
Temperature display in °F or °C
Battery replacement indicator
5-2 programming including:
- Preprogrammed energy-saving schedule
- Early Start
- Temporary bypass
- Time display (12 h or 24 h)
Filter replacement indicator

2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT
POWER TO THE HEATING SYSTEM.

n Remove the old thermostat to access the wires.

Warning: If the old thermostat was mounted onto an electrical box,
it was probably powered by 120/240 volts. In this case, this thermo-
stat cannot be used.
o Identify and label each wire (with the corresponding letter on
the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire (maximum of 1/4 inch).

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to
avoid air draughts behind the thermostat.

2.2 Installing the New Baseplate

For a new installation, choose a location approximately 5 feet
(1.5 m) above the floor and on an inside wall. Avoid draughty
areas (top of staircase, air outlet, etc.), dead air spots (behind
doors), direct sunlight or areas near concealed pipes or chim-
neys.

n Remove the thermostat faceplate.

o Loosen the locking screw to separate the thermostat from its

baseplate (the screw cannot be completely removed).

p Tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

2.3 Connecting the Thermostat

The connection of the new thermostat should be similar to that of
the old thermostat; however, it can vary depending on the installa-
tion.
Note: The red jumper wire between the Rc and Rh terminals must
be removed in 2- or 5-wire installations. The jumper must be used in
3- or 4-wire installations if you wish to use the mode selector switch
for the fan.

1. Introduction

2. Installation

RTH230B

Programmable Electronic Thermostat

Installation and User Guide

Display
Adjustment
buttons
System operating
mode selector
Fan operating
mode selector
Programming
buttons
Rh Heating power supply
Rc Cooling power supply
W Heating signal
Y Cooling signal
GFan

मैनुअल देखें Honeywell RTH230B यहाँ, मुफ्त में। यह मैनुअल श्रेणी के अंतर्गत आता है थर्मोस्टेट और मूल्यांकन किया गया है 2 औसत वाले लोग द्वारा 9.2. यह मैनुअल निम्नलिखित भाषाओं में उपलब्ध है: अंग्रेज़ी . क्या आपके पास के बारे में कोई प्रश्न है? Honeywell RTH230B या आपको मदद चाहिए? अपना प्रश्न यहाँ पूछें

मदद की ज़रूरत है?

क्या आपके पास इसके बारे में कोई प्रश्न है? Honeywell और क्या उत्तर मैनुअल में नहीं है?

  • समाधान पर अपडेट प्राप्त करें
  • अपने प्रश्न का उत्तर प्राप्त करें

सवाल और जवाब

प्रश्नों की संख्या: 0

हनीवेल RTH230B थर्मोस्टैट हनीवेल RTH230B एक प्रभावी थर्मोस्टैट है जो आपको अपने घर के तापमान को नियंत्रित करने में मदद करता है। यह थर्मोस्टैट उच्च गुणवत्ता वाले सामग्री से बना है जो इसे एक टिकाऊ और टिकाऊ विकल्प बनाती है। आपको यह थर्मोस्टैट अपनी मनचाही रंग चयनित करने का विकल्प देता है, इससे आपको आपके इंटीरियर के अनुसार इसके साथ मिलती है। हनीवेल RTH230B थर्मोस्टैट के अतिरिक्त विशेषताएं हैं जो इसे अन्य विकल्पों से पृथक्करती हैं। यह थर्मोस्टैट आपको आपके घर के तापमान को सेट करने के लिए परमिटर विकल्प भी देता है, जिससे आप आसानी से अपने आवश्यकतानुसार उचित तापमान की सेटिंग कर सकते हैं। इसके साथ ही, इसमें हीटिंग और कूलिंग के लिए अलग-अलग सेटिंग्स भी होती हैं, जो आपको माहौल के अनुसार उचित तापमान की प्राथमिकता देती हैं। इसका प्रयोग करना भी बहुत आसान है। आपको सिर्फ इसे अपनी पसंदीदा सेटिंग्स में सेट करना होगा और यह आगे से आपके तापमान को सेट करेगा। एक बार तापमान बार-बार नहीं सेट करना पड़ेगा। यह थर्मोस्टैट आपके जीवन को सुखी और आरामदायक बनाने के लिए अत्यंत महत्वपूर्ण है। इसकी प्रमुख जानकारी: - प्रीसिजन तापमान नियंत्रण प्रणाली - उच्च गुणवत्ता वाले सामग्री और टिकाऊ निर्माण - अपनी पसंदीदा रंग के विकल्प - सेटिंग करने के लिए परमिटर विकल्प - हीटिंग और कूलिंग के लिए अलग-अलग सेटिंग्स - आसान इंस्टालेशन और उपयोग

आम
ब्रांडHoneywell
आदर्शRTH230B
उत्पादथर्मोस्टेट
भाषाअंग्रेज़ी
फाइल का प्रकारउपयोगकर्ता पुस्तिका (PDF)

निर्देश पुस्तिका में आपके प्रश्न का उत्तर नहीं मिल रहा है? आपको अपने प्रश्न का उत्तर Honeywell RTH230B के बारे में अक्सर पूछे जाने वाले प्रश्नों में मिल सकता है।

थर्मोस्टेट लगाने के लिए सबसे अच्छी जगह कहाँ है?

थर्मोस्टेट के लिए सबसे अच्छी जगह वह कमरा है जहाँ आप सबसे अधिक समय बिताते हैं, कई मामलों में लिविंग रूम या किचन। थर्मोस्टैट को फर्श से लगभग डेढ़ मीटर ऊपर रखें, न धूप में और न ही किसी बाहरी दीवार पर।

थर्मोस्टेट का डेड बैंड क्या होता है?

यदि आपके थर्मोस्टैट में एक डेड बैंड है, तो आपका इंस्टॉलेशन, जैसा कि वह था, 'आराम पर' है। थर्मोस्टैट तभी चालू होता है जब, उदाहरण के लिए, अंतर सेट कमरे के तापमान से 2˚C से अधिक विचलित हो जाता है।

आदर्श कमरे का तापमान क्या है?

ज्यादातर लोग पाते हैं कि आदर्श कमरे का तापमान 19 से 22 डिग्री सेल्सियस के बीच होता है।

मैनुअल Honeywell RTH230B में उपलब्ध है हिंदी?

दुर्भाग्य से, हमारे पास इसके लिए मैनुअल नहीं है Honeywell RTH230B में उपलब्ध हिंदी . यह मैनुअल में उपलब्ध है अंग्रेज़ी .

क्या आपका प्रश्न सूचीबद्ध नहीं है? अपना प्रश्न यहाँ पूछें

कोई परिणाम नहीं